- Bộ lập trình PLC, cáp lập trình
- Màn hình HMI
- Cảm biến, phụ kiện
- Biến tần, khởi động mềm
- Máy cắt, Aptomat, khởi động từ
- Thiết bị đo lường, bảo vệ
- Thiết bị công nghiệp, tự động hóa
- Thủy lực, khí nén, van công nghiệp
- Motor, Servo motor, Servo Amplifier
- Thyristor, Module, SCR, SSR, Diode
- Phụ kiện tủ điện và vỏ tủ điện
- Cáp điện, ống bảo vệ cáp
- Thiết bị điện trung thế, truyền tải
- Thiết bị chống sét, kim thu sét
- Dụng cụ cầm tay, dụng cụ tool
- ATS, UPS, tụ bù, cuộn kháng
-
Thiết bị ngành xi măng, thép, nhiệt điện
-
Thiết bị thanh lí-hàng tháo máy
Đồng hồ đo điện áp, dòng điện hiển thị số PA194I-9X4 three-phase ammeter, PZ194U-9X4 three-phase voltmeter.
PA194I-9X4 three-phase ammeter, PZ194U-9X4 three-phase voltmeter.
Overview SX6L is an intelligent three-phase ammeter that can simultaneously measure three-phase current parameters in a three-phase power grid. It can be equipped with RS485 digital communication function to realize remote monitoring.
Overview SX6L is an intelligent three-phase ammeter that can simultaneously measure three-phase current parameters in a three-phase power grid. It can be equipped with RS485 digital communication function to realize remote monitoring.
Technical Parameters
characteristic
The main function of the intelligent three-phase ammeter is to measure the three-phase current of the power grid. The three-row digital tube is displayed at the same time. It can be equipped with RS485 communication interface, transmission output (analog output), upper and lower limit alarm, and can directly set the current change on site. Than, it is very convenient to use.
Features and features:
1. Display magnification, communication address, baud rate, etc. can be set arbitrarily through the buttons on the panel, which is very flexible and convenient to use.
2. All can be equipped with 1 analog output, can choose the measured transmission output, the output is 4~20mA, 0~5V, 0~12~20mA, etc.
3. Optional relay alarm output, monitoring the upper and lower limits of the measured parameters.
4. It can be equipped with RS-485 digital interface and adopts standard MODBUS-RTU protocol.
5. Wide application range and strong combination function.
6. Digital zero calibration, digital calibration, high precision and high cost performance.
The accuracy level voltage and current meter are 0.5 and 0.2; the frequency meter is 0.1; the power and power factor meter is 0.5.
Display mode three and a half LED display or four-digit display
Input nominal input current and current AC1A, AC5A, AC10A, AC500mA, DC5A, DC20mA, etc.
Voltage and voltage AC100V, AC220V, AC380V, DC100V, DC200V, DC380V, DC75mV, etc.
Overload duration: 1.2 times instantaneous: voltage 2 times (10 seconds), current 10 times (5 seconds)
Frequency 50/60Hz±10%
Power auxiliary power switching power supply: AC, DC80~270V, linear power supply: AC220V±5%
Power consumption insulation strength AC2kV
Insulation resistance ≥100MΩ
Mean time between failures ≥50000h
Working conditions Ambient temperature: -10~55°C, relative humidity ≤93%, no corrosive gas, altitude ≤2500m
Tình trạng sản phẩm:
Precautions
1. Before use, the meter needs to be powered for 15 minutes.
2, pay attention to prevent vibration and shock, do not use in places with excessive dust and excessive harmful gases.
3. The input wire should not be too long. If the input end of the signal to be tested is long, please try the twisted pair shielded wire.
4. If the signal is accompanied by high frequency interference, the low frequency filter should be tested online.
5. When not storing for a long time, please power on every three months for not less than 4 hours.
6, long-term preservation should avoid direct light, should be stored in the ambient temperature -25 ° C ~ 55 ° C.
7. If the meter has no display, check the auxiliary power supply first, and the voltage is within the range.
8. If the display is not normal, check if the input signal is normal and the signal terminal is tight.
9. Unless the PT has sufficient power, the PT signal cannot be used as an auxiliary power source at the same time to ensure the normal operation of the meter.
10. The current terminal screw in the CT circuit must be tightened to ensure reliable contact between the incoming and outgoing wires to avoid malfunction.
11. If the instrument is to be calibrated, the calibration instrument should be better than 0.1 to ensure the calibration accuracy.
Specializing in the production of digital tube display, single, three-phase ammeter, single, three-phase voltmeter, PZ568 series multi-function power meter, network multi-function power meter, single, three-phase active power meter, three-phase reactive power meter, three-phase power Factor table, single-phase power factor meter, frequency meter, electric energy meter, etc., single-phase, three-phase current transmitter, single-phase voltage transmitter, three-phase voltage transmitter, active power transmitter, power factor transmission Device
TÂN THÀNH CAM KẾT
- Sản phẩm, hàng hóa chính hãng.
- Giá cả cạnh tranh.
- Dịch vụ chăm sóc khách hàng tận tâm.
Thông Tin Công Ty
Chính sách và quy định
Đã thông báo
Hỗ trợ khách hàng
THÔNG TIN LIÊN HỆ:
-------------------------------
CÔNG TY TNHH THIẾT BỊ CÔNG NGHIỆP TTH
Trụ sở: số 124 ngõ 79 Yên Hoà-Cầu giấy-HN
Kinh doanh 1 : 0816.861.515
Kinh doanh 2 : 0836.861.515
Email: tthkinhdoanh@gmail.com
Email: tthkinhdoanh01@gmail.com
