Rơ le bảo vệ, Phoenix Relay PSR-SCP- 24UC/ESA2/4X1/1X2/B Safety Relay 2936802

Đăng ngày 01-10-2018 02:12:59 AM - 629 Lượt xem

Mã sản phẩm: PSR-SCP- 24UC/ESA2/4X1/1X2/B

size

Ambient temperature (running)	-20 °C ... 65 °C (note the reduced value)
Ambient temperature (storage/transportation)	-40 °C ... 70 °C
Maximum relative humidity allowed (operating)	75 % (average, 85% intermittent, no condensation)
Maximum allowable humidity (storage/transport)	75 % (average, 85% intermittent, no condensation)
electric shock	15g
Vibration (operation)	10 Hz ...150 Hz, 2g
maximum height	≤ 2000 m (above sea level)

Rated control power supply voltage U _S	24 V AC/DC -15 % / +10 %
Power consumption at U _S	Typ. 3.36 W (AC)
	Typ. 1.56 W (DC)
Rated control power supply current I _S	Typ. 140 mA AC
	Typ. 65 mA DC
Typical inrush current	2 A (when Δt = 10 μs U _s )
Electricity consumption	< 50 mA (U _s /I _x to S12)
	0 mA (U _s /I _x to S34)
Input/start-up and feedback circuit voltage	24 V DC -15 % / +10 %
Typical response time	< 65 ms (automatic start)
	< 40 ms (manual reset)
Typical suction time	< 65 ms (when controlled by A1)
Typical release time	< 45 ms (when controlled by S12)
	< 200 ms (when controlled by A1)
Parallel input 1/2	∞
Recovery Time	< 1 s
Status Display	2 x green LED
Maximum switching frequency	1 Hz
Allowable maximum total resistance of the wire	Approximately 22 Ω ( input and start-up circuitry at U _S )

Contact type	4-way normally open safety contact output
	1 feedback loop
Contact material	AgSnO ₂
Minimum switching voltage	15 V AC/DC
Maximum switching voltage	250 V AC/DC
Limit continuous current	6 A (N/O contact)
	6 A (normally closed contact)
Minimum inrush current	25 mA
Maximum starting current	6 A
Square of total current value	72 A ² (see attenuation curve)
Maximum rated power value (resistive load)	144 W (24V DC, τ = 0ms, normally closed contact 51/52: 72W)
	288 W (48V DC, τ = 0ms, normally closed contact 51/52: 144W)
	110 W (110VDC, t=0ms)
	88 W (220VDC, t=0ms)
	1500 VA (250V AC, τ = 0ms, normally closed contact 51/52: 750VA)
Maximum rated power value (inductive load)	42 W (24V DC, τ=40ms)
	42 W (48V DC, τ=40ms)
	42 W (110V DC, τ=40ms)
	42 W (220V DC, τ=40ms)
	42 W (250 V AC, τ = 40 ms)
Minimum on-off capacity	0.4 W
Output fuse	6 A fast blow
	C6 (24VAC/DC) automatic equipment

Connection method	Screw connection
Pluggable	Yes
Minimum cross section of rigid wire	0.2 mm2
Maximum cross section of rigid wire	2.5 mm2
Flexible conductor minimum cross section	0.2 mm2
Maximum cross section of flexible wire	2.5 mm2
Minimum wire cross section AWG	twenty four
Maximum wire cross section AWG	12
Stripping length	7 mm
Thread	M3

Relay model	Motor integrated relay with forced guiding contact according to EN 50205
Mechanical life	10 x 10 ⁶ switching times
net weight	249.8 g
Installation type	DIN rail mounting
Assembly instructions	See attenuation curve
Protection level	IP54
Enclosure rating	IP20
Insert position minimum protection level	IP54
Installation location	Vertical or horizontal
control	Single channel
Parameters for EN 13849	1 (up to 4 categories depending on the application)
Stop category	0
IEC 61508 parameters	1
name	Clearance and creepage distance between power supply circuits
Standard / procedure	DIN EN 50178/VDE 0160
Rated overvoltage / insulation	4 kV basic safety isolation: 6 kV reinforced isolation withstand voltage between all current paths and the enclosure : S11/S12/S33/S34 between A1/A2 and 13/14, 23/24, 33/34, 43/44 Between 51/52 and 13/14, 23/24, 33/34, 43/44 between 13/14, 23/24, 33/34 and 43/44
Rated insulation voltage	250 V AC
Pollution level	2
Surge voltage category	III
Housing material	PBT