- Bộ lập trình PLC, cáp lập trình
- Màn hình HMI
- Cảm biến, phụ kiện
- Biến tần, khởi động mềm
- Máy cắt, Aptomat, khởi động từ
- Thiết bị đo lường, bảo vệ
- Thiết bị công nghiệp, tự động hóa
- Thủy lực, khí nén, van công nghiệp
- Motor, Servo motor, Servo Amplifier
- Thyristor, Module, SCR, SSR, Diode
- Phụ kiện tủ điện và vỏ tủ điện
- Cáp điện, ống bảo vệ cáp
- Thiết bị điện trung thế, truyền tải
- Thiết bị chống sét, kim thu sét
- Dụng cụ cầm tay, dụng cụ tool
- ATS, UPS, tụ bù, cuộn kháng
-
Thiết bị ngành xi măng, thép, nhiệt điện
-
Thiết bị thanh lí-hàng tháo máy
Đồng hồ hiển thị nhiệt đô đa kênh, XMD52216, XMD52208, XMD50208
★ Scope of application
It is applicable to the patrol monitoring and alarm control of various industrial process parameters such as shaft temperature, pipeline air temperature and furnace temperature.
Tình trạng sản phẩm:
★ Scope of application
It is applicable to the patrol monitoring and alarm control of various industrial process parameters such as shaft temperature, pipeline air temperature and furnace temperature.
★ Features
※ Universal input signal
It can be applied to any of the following input signals with simple software and hardware settings.
l Thermal resistance: Pt100, Pt100.0, Pt10, Cu50, Cu100.
l Thermocouple: K, E, S, B, J, R, T, N, with automatic cold junction temperature compensation.
l Standard signal: 0-10mA, 4-20mA, 0-5V, 1-5V, linear or square signal.
l Remote transmission pressure gauge: 30-350 W , the signal deviation can be corrected by the on-site button, that is, ready to use.
l General linear non-standard signal: 0-60mV or 0-60mV or more 0-5V or any signal can be set to use immediately.
l Other special customized non-standard input signals.
※ Single-chip intelligent
l Zero point and magnification can be automatically tracked, and there is no drift in long-term operation.
l All parameters can be set by pressing the button.
※ Alarm relay
l There are up to two common alarm relays, and the common alarm relay has two alarm modes that can be selected by pressing the button.
l “Common” alarm: The relay will act as long as any channel generates an alarm.
l “Specified channel”: The relay will only operate if an alarm is generated on a specified channel.
l Each channel alarm value and alarm hysteresis can be set separately.
※ There are also road and lower limit alarm indicators on the 24 circuit inspection instrument panel.
※ With RS485/ RS232/Modem isolated communication interface
※ With serial print port, it can be used with our PRN5000 disk printer.
※ 8/16 loop inspection instrument can be equipped with DT500 each channel alarm control expansion box, each channel alarm control expansion box each box has 16 alarm control output relays, there are 4 types available.
l DT501:1-8 channel upper and lower limit alarm control output expansion box.
l DT502: 9-16 channel upper and lower limit alarm control output expansion box.
l DT503: 1-16 channel upper limit alarm control output expansion box.
l DT504: 1-16 channel lower limit alarm control output expansion box.
★ XMD5000 series / DT500 series selection table
| Spectrum | Description | ||||||||
| XMD | Multi-channel inspection instrument | ||||||||
| Design sequence | 5 | Switching power supply | |||||||
| Control type | 0 | Without control alarm | |||||||
| 1 | With a common upper or lower alarm output | ||||||||
| 2 | With common upper and lower alarm output | ||||||||
| 3 | With each road, lower limit alarm output (with DT500) | ||||||||
| input signal Types of | 1 | Adapter thermocouple | |||||||
| 2 | Adapter thermal resistance | ||||||||
| 3 | Adapter Hall Transmitter | ||||||||
| 4 | Adapted to remote pressure gauge | ||||||||
| 5 | Adapt DC 0~10mA input | ||||||||
| 6 | Adapt DC 4~20mA input | ||||||||
| 7 | Adapt to DC 0~5V input | ||||||||
| 8 | Adapt to DC 1~5V input | ||||||||
| U | Universal index number input | ||||||||
| Input Number of channels | 08 | Eight channels | |||||||
| 16 | Sixteen channels | ||||||||
| twenty four | Twenty-four channels | ||||||||
| external structure Types of | 160×80×150mm horizontal table | ||||||||
| V | 80×160×150mm vertical table | ||||||||
| F | Unable to enter universal index number | 96×96×110mm square meter (only 8 channels have this option) | |||||||
| Power supply Types of | Power supply 220VAC | ||||||||
| D | Power supply 24VDC | ||||||||
| Communication Interface Types of | Without communication interface | ||||||||
| RS232 | RS232 isolated communication interface | ||||||||
| RS485 | RS485 isolated communication interface | ||||||||
| MODEM | Modem isolation interface | ||||||||
| PRN | Serial standard print interface | ||||||||
| Alarm Output Expansion box | 8 channels and 16 channels have this function at the same time | -DT501 | 1-8 channel upper and lower limit alarm control output expansion box | ||||||
| -DT502 | 9-16 channel upper and lower limit alarm control output expansion box | ||||||||
| Only 16 channels have this function | -DT503 | 1-16 channel upper limit alarm control output expansion box | |||||||
| -DT504 | 1-16 channel lower limit alarm control output expansion box | ||||||||
| Special function code | □□□□ | 0000 means no special function code | |||||||
TÂN THÀNH CAM KẾT
- Sản phẩm, hàng hóa chính hãng.
- Giá cả cạnh tranh.
- Dịch vụ chăm sóc khách hàng tận tâm.
Thông Tin Công Ty
Chính sách và quy định
Đã thông báo
Hỗ trợ khách hàng
THÔNG TIN LIÊN HỆ:
-------------------------------
CÔNG TY TNHH THIẾT BỊ CÔNG NGHIỆP TTH
Trụ sở: số 124 ngõ 79 Yên Hoà-Cầu giấy-HN
Kinh doanh 1 : 0816.861.515
Kinh doanh 2 : 0836.861.515
Email: tthkinhdoanh@gmail.com
Email: tthkinhdoanh01@gmail.com
