- Bộ lập trình PLC, cáp lập trình
- Màn hình HMI
- Cảm biến, phụ kiện
- Biến tần, khởi động mềm
- Máy cắt, Aptomat, khởi động từ
- Thiết bị đo lường, bảo vệ
- Thiết bị công nghiệp, tự động hóa
- Thủy lực, khí nén, van công nghiệp
- Motor, Servo motor, Servo Amplifier
- Thyristor, Module, SCR, SSR, Diode
- Phụ kiện tủ điện và vỏ tủ điện
- Cáp điện, ống bảo vệ cáp
- Thiết bị điện trung thế, truyền tải
- Thiết bị chống sét, kim thu sét
- Dụng cụ cầm tay, dụng cụ tool
- ATS, UPS, tụ bù, cuộn kháng
-
Thiết bị ngành xi măng, thép, nhiệt điện
-
Thiết bị thanh lí-hàng tháo máy
WTZK-02 transformer temperature controller pressure type temperature controller thermostat WTZK-03
First, use and principle
WTZK-02/03 type temperature controller (BWY-02/03 type temperature controller), suitable for measuring the temperature of transformer oil or other liquids, gases and vapors, and can reach and exceed the set value at the measured temperature. The contact signal is issued. This instrument is mainly used for measuring and controlling the oil temperature of transformers above 500KVA. The main structure of the controller consists of a thermostat (temperature probe) capillary and elastic components. The sealing system composed of these three components is filled with the temperature sensing medium. When the measured temperature changes, the liquid pressure in the temperature pack changes with the capillary, and the elastic element of the meter head produces a corresponding one. The displacement amount, which is mechanically amplified, can indicate the measured temperature and drive the micro-switch action output signal.
WTZK-02/03 type temperature controller (BWY-02/03 type temperature controller), suitable for measuring the temperature of transformer oil or other liquids, gases and vapors, and can reach and exceed the set value at the measured temperature. The contact signal is issued. This instrument is mainly used for measuring and controlling the oil temperature of transformers above 500KVA. The main structure of the controller consists of a thermostat (temperature probe) capillary and elastic components. The sealing system composed of these three components is filled with the temperature sensing medium. When the measured temperature changes, the liquid pressure in the temperature pack changes with the capillary, and the elastic element of the meter head produces a corresponding one. The displacement amount, which is mechanically amplified, can indicate the measured temperature and drive the micro-switch action output signal.
Tình trạng sản phẩm:
Second, the main technical parameters
1. Measurement range: 0~100°C
2. Indication accuracy: 1.5
3. Switching characteristics
(1) Switch setting accuracy: ±3 °C
(2) Switching difference: 6±2°C
(3) Switch rated load: AC220V, 1.5A
4. Warm pack size: ф14×150
5. Warm package installation size: external thread M27×2
6. Head mounting size: 3 holes ф6 144×210
7. The standard setting value of the switch when the instrument is shipped from the factory: first upper limit 55 °C second upper limit 80 °C
If the user needs to adjust the switch setting, open the cover, turn the dial on the dial to set the needle, and then close the cover as it is.
Third, installation and use
1. Temperature setting: Open the cover and turn the knob to set the needle (usually no need to set).
2. Wiring: Open the cover and thread the cable from the lead contact. Wire as shown in Figure 2. The KW4×1.5 control cable is recommended for the cable.
Tighten the nut at the lead connector after wiring and do not loosen. The cover is assembled as it is, and the four screws are evenly tightened.
Before installing the thermostat head, complete the installation wiring and switch setting.
1. Measurement range: 0~100°C
2. Indication accuracy: 1.5
3. Switching characteristics
(1) Switch setting accuracy: ±3 °C
(2) Switching difference: 6±2°C
(3) Switch rated load: AC220V, 1.5A
4. Warm pack size: ф14×150
5. Warm package installation size: external thread M27×2
6. Head mounting size: 3 holes ф6 144×210
7. The standard setting value of the switch when the instrument is shipped from the factory: first upper limit 55 °C second upper limit 80 °C
If the user needs to adjust the switch setting, open the cover, turn the dial on the dial to set the needle, and then close the cover as it is.
Third, installation and use
1. Temperature setting: Open the cover and turn the knob to set the needle (usually no need to set).
2. Wiring: Open the cover and thread the cable from the lead contact. Wire as shown in Figure 2. The KW4×1.5 control cable is recommended for the cable.
Tighten the nut at the lead connector after wiring and do not loosen. The cover is assembled as it is, and the four screws are evenly tightened.
Before installing the thermostat head, complete the installation wiring and switch setting.
TÂN THÀNH CAM KẾT
- Sản phẩm, hàng hóa chính hãng.
- Giá cả cạnh tranh.
- Dịch vụ chăm sóc khách hàng tận tâm.
Thông Tin Công Ty
Chính sách và quy định
Đã thông báo
Hỗ trợ khách hàng
THÔNG TIN LIÊN HỆ:
-------------------------------
CÔNG TY TNHH THIẾT BỊ CÔNG NGHIỆP TTH
Trụ sở: số 124 ngõ 79 Yên Hoà-Cầu giấy-HN
Kinh doanh 1 : 0816.861.515
Kinh doanh 2 : 0836.861.515
Email: tthkinhdoanh@gmail.com
Email: tthkinhdoanh01@gmail.com
